Test, simulation and calculation methods of vehicles and components
- F2010C028
- Design and Experimental Evaluation of Predictive Engine Air-ratio Control Based on Online Neural Network
- Mr. Hang Cheong Wong, University of Macau, China
- F2010C044
- The Human Thermal Comfort Evaluation Inside the Passenger Compartment
- Dr. Mariana Ivanescu, University of Pitesti, Romania
- F2010C046
- Electro-chemical Degradation Analysis of a Coolant Rubber Hose for Automotive Radiator
- Mr. Seung-Bum Kwak, Hanyang Univ., Korea
- F2010C079
- On-Board Diagnostics of Combustion in Diesel Engines of Non-Road Vehicles with the Use of JTFA Vibration Signal Analyses
- Prof. Jerzy Merkisz, Poznan University of Technology, Poland
- F2010C087
- Investigations of Vehicle Exhaust Emissions with Use PEMS
- Ph.D. Wojciech Gis, Motor Transport Institute, Poland
- F2010C089
- Evaluation of Quality of the System for Control of MixtureComposition in SI Engine by the Method of Dynamic Simulation
- Prof. Józef Nita, Technical University of Radom, Poland
- F2010C135
- Method and Tool of Human Sensation Modeling for Comfort Evaluation of NVH Phenomenon on the Example of Gear Rattle
- Prof. Dr.-Ing. Dr. h. c. Albert Albers , IPEK - Institute of Product Engineering; Karlsruhe Institute of Technology (KIT), Germany
- F2010C202
- Measurement and Analysis of FlexRay Synchronization Performance
- Mr. Jin Ho Kim, Sungkyunkwan Univ., Korea
- F2010C227
- The Information Content of the Automatic Gearboxes
- Mr. Ferenc Szauter, Széchenyi István University, Hungary
Posters with Brief Oral Introduction
A selected number of Poster Authors have been offered the opportunity to make a short presentation about the content of their Posters (PBOIs - Posters with Brief Oral Introduction) during a Technical Session which addresses the same topic. PBOI authors will be available to meet with delegates for in-depth discussions about their posters during the refreshment and lunch breaks which follow the Technical Session in which their PBOI is included.
- F2010C011
- Examination of Manual Transmission Gear Jump Out Behavior
- Mr. Takanori Nukata, Toyota Motor Corporation, Japan
- Session: Testing and Simulation of Vehicle and Component Dynamics
- F2010C017
- Customer Benefit of HEV in Real Traffic
- Mrs. Marjam Eghtessad, Institute of Automotive Engeneering, Technical University of Braunschweig, Germany
- Session: Alternative Drivelines
- F2010C031
- Methodology of Service Life Estimation for Automotive Rubber Component
- Dr. Changsu Woo, KIMM, Korea
- Session: Testing and Simulation of Vehicle and Component Dynamics
- F2010C034
- Nonlinear Static Analysis of an Exhaust System using OptImal Neural Network
- Mr. Francisco Javier Asensio, Citean Fundacion Cetena, Spain
- Session: Tools and Methods for Vehicle Systems
- F2010C040
- Optimum SUV Bumper System Design Considering the Pedestrian Performance
- Mr Dongkyou Park, Hyundai-Kia Motors, Korea
- Session: Passive Safety Issues
- F2010C055
- MBS Quarter Vehicle -Influence of Damper Modelling on Simulation Quality
- Mr. Georg Klose, TU Braunschweig, Institute Of Automotive Engineering, Germany
- Session: Testing and Simulation of Vehicle and Component Dynamics
- F2010C057
- Objectification of Shift Quality - Requirement for Effective Transmission Calibration
- Mr. Artur Plötner, Institute of Automotive Engineering, TU Braunschweig, Germany
- Session: Tools and Methods for Vehicle Systems
- F2010C066
- Application of Cross-Correlation Techniques in Four-poster Rig Durability Tests
- Dr. Juan J. García, Applus+ IDIADA, Spain
- Session: Advanced Engineering Technologies and Tools
- F2010C081
- Development of Principles and Methods of Estimation of Thermal Condition of Semitransparent Coatings in Complex Heat Exchange Combustion Chambers for Low-Heat-Rejection Diesel Engines
- Prof. Vladimir Merzlikin, Moscow State Technical University MAMI, Russia
- Session: IC Engines, Goals and Development
- F2010C123
- Simulation Environment for the Development of Predictive Safety Systems
- Mr. Tobias Dirndorfer, TU München (Department of Informatics, Robotics and Embedded Systems), Germany
- Session: Mixed Topics in Safety
- F2010C151
- Estimation of Road Information from Running Vehicle
- Dr. Shigeyuki Yamabe, The University of Tokyo, Japan
- Session: Vehicle Performance Tests and Simulations
- F2010C165
- Multi Scale Modelling as a Tool Increasing the FE Model Potential
- Mr. Karel Benes, Mecas ESI, Czech Republic
- Session: Advanced Engineering Technologies and Tools
- F2010C180
- Method for Model based Monitoring of Complex Mechatronic Systems
- Mr. Achim Seifermann, KIT - Karlsruhe Institute of Technology, Germany
- Session: Tools and Methods for Vehicle Systems
- F2010C198
- Simulation of a Spark Ignition Engine Functioning with Cylinders Deactivation
- Mr. Valerian Croitorescu, University Politehnica of Bucharest, Romania
- Session: IC Engines, Goals and Development
- F2010C221
- Fatigue Life Prediction of a Bus Body Structure using CAE Tools
- Mr. Namik Kilic, Otokar Otobus Karoseri San A.S., Turkey
- Session: Buses